[ Pobierz całość w formacie PDF ]
[*][2][N][#] deletes the Nth telephone number
In addition to the digits 0,1...9 , you can put the following special characters in a telephone number:
Special Method of
Function
character programming
Switches to alternate dialing system, i.e. from DTMF to PULSE or
HEX. B [*][1][*]
inversely
HEX. C [*][2][*] 4-second break in dialing
HEX. D [*][3][*] waiting for a dial tone (DT)
- 9 -
D09 v4.0 EN.doc Rev. A 2008-11-18
Note: Dialer enables programming of eight telephone numbers, two of them can be declared as numbers to a pager, (see Installer Programming
commands [54] and [55]). During the telephone alarm action dialer send text message to those two pager numbers instead of voice alarm
message.
[*][3][N][#] Display the Nth telephone number
After entering the function, the LED's display the first digit of a telephone number in the HEX system. By pressing the [*] key, you can display the
next digit of the number. The dialer automatically exits the function after displaying the last digit of the telephone number or immediately after
you have used the [#] key.
[*][4] Recording of Voice Alarm Message
You can record an alarm announcement by speaking to the built-in microphone from a distance of about 20 cm. The announcement recording is
finished and the function is abandoned automatically after 24 seconds. You can complete the announcement recording earlier by pressing the
[#] key.
[*][5] Playback of Vice Alarm Message
You can listen to the alarm announcement using the headphone socket in the side wall of the dialer. The dialer terminates the announcement
playback and exits the function automatically after the complete announcement has been played back or you can do it earlier by using the [#]
key. Use stereo headphones with a stereo mini-jack plug (diameter 3.5mm).
[*][6][N][code][#] Programming Dialer s Codes
The digit N indicates which code will be programmed. The digits, which are entered during programming, are displayed by the LED's in the HEX
format. The dialer does not allow to program two identical codes. Any attempt to program a code which already exists will result in the error
signal.
Code Number Short Name Description
N=0 [KU0] Main code.
N=1 [KU1] User code.
When you enter the code at the beginning of the external call, you can listen to the dialer status
N=2 [KU2]
announcement and then to go to the tone remote control mode,
N=3 [KU3] he code resets the announcement notification action and pager system notification action,
N=4 [KU4] Dialer Disarming code, can be used via DTMF, after first use code is automatically one-time only,
N=5 [KU5] Disarming code, used via DTMF only, can be used only one time,
N=6 [KU6] Disarming code, used via DTMF only, can be used only one time,
N=7 [KU7] Disarming code, used via DTMF only, can be used only one time,
N=8 [KU8] PGM1 output control code, can be used to set or clear output.
N=9 [KU9] PGM2 output control code, can be used to set or clear output.
[*][7][HHMM][#] Setting the Clock
HH mean the hour and MM mean the minutes. The entered HHMM digits are displayed in the HEX. Example:
Example: [*][7]1243][#] programs the time: 12 hours 43 minutes
[*][8] Display Clock
When you enter the function, the LED's present the first digit of the clock time in the HEX system. The next digits are displayed when you use
the [*] key. The function is abandoned automatically after reading the last digit or you can do it at any time by pressing the [#] key.
[*][9][N] Display Nth Code
When you enter the function, the first digit of the Nth code in the HEX system is presented. You display the next digits with the [*] key. The
function is accomplished automatically after reading the last digit of code or you can do it earlier by pressing the [#] key.
[*][#] Exit from programming
The dialer exits the programming mode and returns to normal operation.
- 10 -
D09 v4.0 EN.doc Rev. A 2008-11-18
INSTALLER PROGRAMMING
You can enter the installer programming mode only when dialer stay in User Programming mode.
[*][0][KI][#]
When dialer stay in Installer Programming mode the LED PROGRAM and LED SYSTEM are on. In this mode, you can enter functions which will [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl wyciskamy.pev.pl
[*][2][N][#] deletes the Nth telephone number
In addition to the digits 0,1...9 , you can put the following special characters in a telephone number:
Special Method of
Function
character programming
Switches to alternate dialing system, i.e. from DTMF to PULSE or
HEX. B [*][1][*]
inversely
HEX. C [*][2][*] 4-second break in dialing
HEX. D [*][3][*] waiting for a dial tone (DT)
- 9 -
D09 v4.0 EN.doc Rev. A 2008-11-18
Note: Dialer enables programming of eight telephone numbers, two of them can be declared as numbers to a pager, (see Installer Programming
commands [54] and [55]). During the telephone alarm action dialer send text message to those two pager numbers instead of voice alarm
message.
[*][3][N][#] Display the Nth telephone number
After entering the function, the LED's display the first digit of a telephone number in the HEX system. By pressing the [*] key, you can display the
next digit of the number. The dialer automatically exits the function after displaying the last digit of the telephone number or immediately after
you have used the [#] key.
[*][4] Recording of Voice Alarm Message
You can record an alarm announcement by speaking to the built-in microphone from a distance of about 20 cm. The announcement recording is
finished and the function is abandoned automatically after 24 seconds. You can complete the announcement recording earlier by pressing the
[#] key.
[*][5] Playback of Vice Alarm Message
You can listen to the alarm announcement using the headphone socket in the side wall of the dialer. The dialer terminates the announcement
playback and exits the function automatically after the complete announcement has been played back or you can do it earlier by using the [#]
key. Use stereo headphones with a stereo mini-jack plug (diameter 3.5mm).
[*][6][N][code][#] Programming Dialer s Codes
The digit N indicates which code will be programmed. The digits, which are entered during programming, are displayed by the LED's in the HEX
format. The dialer does not allow to program two identical codes. Any attempt to program a code which already exists will result in the error
signal.
Code Number Short Name Description
N=0 [KU0] Main code.
N=1 [KU1] User code.
When you enter the code at the beginning of the external call, you can listen to the dialer status
N=2 [KU2]
announcement and then to go to the tone remote control mode,
N=3 [KU3] he code resets the announcement notification action and pager system notification action,
N=4 [KU4] Dialer Disarming code, can be used via DTMF, after first use code is automatically one-time only,
N=5 [KU5] Disarming code, used via DTMF only, can be used only one time,
N=6 [KU6] Disarming code, used via DTMF only, can be used only one time,
N=7 [KU7] Disarming code, used via DTMF only, can be used only one time,
N=8 [KU8] PGM1 output control code, can be used to set or clear output.
N=9 [KU9] PGM2 output control code, can be used to set or clear output.
[*][7][HHMM][#] Setting the Clock
HH mean the hour and MM mean the minutes. The entered HHMM digits are displayed in the HEX. Example:
Example: [*][7]1243][#] programs the time: 12 hours 43 minutes
[*][8] Display Clock
When you enter the function, the LED's present the first digit of the clock time in the HEX system. The next digits are displayed when you use
the [*] key. The function is abandoned automatically after reading the last digit or you can do it at any time by pressing the [#] key.
[*][9][N] Display Nth Code
When you enter the function, the first digit of the Nth code in the HEX system is presented. You display the next digits with the [*] key. The
function is accomplished automatically after reading the last digit of code or you can do it earlier by pressing the [#] key.
[*][#] Exit from programming
The dialer exits the programming mode and returns to normal operation.
- 10 -
D09 v4.0 EN.doc Rev. A 2008-11-18
INSTALLER PROGRAMMING
You can enter the installer programming mode only when dialer stay in User Programming mode.
[*][0][KI][#]
When dialer stay in Installer Programming mode the LED PROGRAM and LED SYSTEM are on. In this mode, you can enter functions which will [ Pobierz całość w formacie PDF ]