[ Pobierz całość w formacie PDF ]
Fig. 28
A) Fix the two lead wires (a, b) from the Controller at the lead holder.
B) Route the lead wires (a, b, c, d, e, f) from the Controller between the rib and the boss.
C) Fix the white lead wire (c) from the Controller at the lead holders.
D) Fix the red lead wire (b) from the Controller at the lead holders.
E) Route the lead wires (b, g, i, j, k) between the rib and the Switch.
F) Route the lead wires (h) from the Power supply cord between the ribs and the wall of the Motor housing.
B A
a
Lead holder
b
c
Boss
d
Rib
e
f
C
D
k
Connectors
j
i
E
Rib
g
Switch
Lead wires
color from to
a black Controller Field
h
b red Controller Switch
white (115V)
c
Controller Field
F
blue (220-240V)
d black Controller Connector
e red Controller Connector
f white Controller Connector
Noise suppressor
g white Switch Field
(not used for some
black or brown Power supply
Thermistor
h
countries.)
cord
white or blue via Controller
i black Switch Connector
j red Switch Connector
k
yellow Switch Connector
P 12 /13
Wiring diagram (1)
2) HP2070F & HP2071F (with LED job light)
Route lead wires as illustrated in Fig. 29.
Fig. 29
A) Fix the two lead wires (a, b) from the Controller at the lead holder.
B) Route the lead wires (a, b, c, d, e, f) from the Controller between the rib and the boss.
C) Fix the white lead wire (c) from the Controller at the lead holders.
D) Fix the red lead wire (b) from the Controller at the lead holders.
E) Route the lead wires (b, g, i, j, k) between the rib and the Switch.
F) Route the lead wires (h, l) as illustrated below in "cross section of F".
G) Route the lead wires as illustrated below.
B A
a
Lead holder
b
c
Boss
d
Rib
e
f
C
Lead wires
D
color from to
k
a black Controller Field
Connectors
b red Controller Switch j
white (115V)
i
c
Controller Field
blue (220-240V)
E
d black Controller Connector
Rib
e red Controller Connector
f white Controller Connector
g
g white Switch Field
Switch
black or brown Power supply
Thermistor
h
cord
white or blue via Controller
i black Switch Connector
j red Switch Connector
k
yellow Switch Connector
h
red (115V)
Case of printed
l
Switch
blue (220-240V)
wiring board
Case of printed
Case of printed
m
white LED
wiring board
wiring board
F
[Cross section of F]
Noise suppressor
Case of printed
m
(Integral part of
wiring board
Light circuit; not
h (lead wires from
used for some
Power supply cord)
LED countries.)
G
l (lead wires from the
Case of printed wiring
Motor housing
board to the Switch)
P 13 /13
Wiring diagram (2)
For all models
Fig. 30
When installing the Brush holder unit on the Motor
housing, set the unit so that its two concave portions
Motor housing
face the direction of the Trigger switch. (Fig. 30)
Brush
holder unit
Place the Connectors as illustrated in Fig. 31.
Do not place it on the side of the U-shaped notch in the
Motor housing.
Concave portions
Note:
Be careful not to pinch the lead wires between the Motor
housing and the Controller.
Fig. 31
Connectors
Controller
Do not pinch the lead wires
Motor housing
between the Motor housing
and the Controller.
U-shaped notch
Keyless drill chuck 13
HP2071 & HP2071F
If the Keyless drill chuck 13 cannot be loosened because of a jammed drill bit, take the following procedures to
loosen the chuck;
1) Fix the sleeve section of the chuck securely with an adjustable spanner, etc. (Fig. 31)
Note: Don not fix the retaining section at this time.
2) And then, with a wrench 19, etc, turn the hex. nut on the top of the chuck clockwise to loosen the chuck. (Fig. 31)
Fig. 31
Retaining ring portion Wrench 19
Sleeve portion
Hex nut
Pipe wrench [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl wyciskamy.pev.pl
Fig. 28
A) Fix the two lead wires (a, b) from the Controller at the lead holder.
B) Route the lead wires (a, b, c, d, e, f) from the Controller between the rib and the boss.
C) Fix the white lead wire (c) from the Controller at the lead holders.
D) Fix the red lead wire (b) from the Controller at the lead holders.
E) Route the lead wires (b, g, i, j, k) between the rib and the Switch.
F) Route the lead wires (h) from the Power supply cord between the ribs and the wall of the Motor housing.
B A
a
Lead holder
b
c
Boss
d
Rib
e
f
C
D
k
Connectors
j
i
E
Rib
g
Switch
Lead wires
color from to
a black Controller Field
h
b red Controller Switch
white (115V)
c
Controller Field
F
blue (220-240V)
d black Controller Connector
e red Controller Connector
f white Controller Connector
Noise suppressor
g white Switch Field
(not used for some
black or brown Power supply
Thermistor
h
countries.)
cord
white or blue via Controller
i black Switch Connector
j red Switch Connector
k
yellow Switch Connector
P 12 /13
Wiring diagram (1)
2) HP2070F & HP2071F (with LED job light)
Route lead wires as illustrated in Fig. 29.
Fig. 29
A) Fix the two lead wires (a, b) from the Controller at the lead holder.
B) Route the lead wires (a, b, c, d, e, f) from the Controller between the rib and the boss.
C) Fix the white lead wire (c) from the Controller at the lead holders.
D) Fix the red lead wire (b) from the Controller at the lead holders.
E) Route the lead wires (b, g, i, j, k) between the rib and the Switch.
F) Route the lead wires (h, l) as illustrated below in "cross section of F".
G) Route the lead wires as illustrated below.
B A
a
Lead holder
b
c
Boss
d
Rib
e
f
C
Lead wires
D
color from to
k
a black Controller Field
Connectors
b red Controller Switch j
white (115V)
i
c
Controller Field
blue (220-240V)
E
d black Controller Connector
Rib
e red Controller Connector
f white Controller Connector
g
g white Switch Field
Switch
black or brown Power supply
Thermistor
h
cord
white or blue via Controller
i black Switch Connector
j red Switch Connector
k
yellow Switch Connector
h
red (115V)
Case of printed
l
Switch
blue (220-240V)
wiring board
Case of printed
Case of printed
m
white LED
wiring board
wiring board
F
[Cross section of F]
Noise suppressor
Case of printed
m
(Integral part of
wiring board
Light circuit; not
h (lead wires from
used for some
Power supply cord)
LED countries.)
G
l (lead wires from the
Case of printed wiring
Motor housing
board to the Switch)
P 13 /13
Wiring diagram (2)
For all models
Fig. 30
When installing the Brush holder unit on the Motor
housing, set the unit so that its two concave portions
Motor housing
face the direction of the Trigger switch. (Fig. 30)
Brush
holder unit
Place the Connectors as illustrated in Fig. 31.
Do not place it on the side of the U-shaped notch in the
Motor housing.
Concave portions
Note:
Be careful not to pinch the lead wires between the Motor
housing and the Controller.
Fig. 31
Connectors
Controller
Do not pinch the lead wires
Motor housing
between the Motor housing
and the Controller.
U-shaped notch
Keyless drill chuck 13
HP2071 & HP2071F
If the Keyless drill chuck 13 cannot be loosened because of a jammed drill bit, take the following procedures to
loosen the chuck;
1) Fix the sleeve section of the chuck securely with an adjustable spanner, etc. (Fig. 31)
Note: Don not fix the retaining section at this time.
2) And then, with a wrench 19, etc, turn the hex. nut on the top of the chuck clockwise to loosen the chuck. (Fig. 31)
Fig. 31
Retaining ring portion Wrench 19
Sleeve portion
Hex nut
Pipe wrench [ Pobierz całość w formacie PDF ]